Introduction
Bescor MP-101 Pan and Tilt head was very useful addition to my photography equipment which allow me to photograph things remotely, but it had one big limitation, well 20ft limitation – extension cord, yes exactly it was remotely controlled with 20ft or upgradable to 50′ piece of wire. Bescor MP101, 2x RE50 & PS260 Complete Kit. Control your camera's pan and tilt remotely with this Motorized Pan & Tilt Head Kit from Bescor. This kit includes the MP-101 Motorized Pan & Tilt Head, a PS-260 AC power supply, a remote control, and two 50' remote extension cables that can be daisy chained together for 100' of extension.
- Incorporate the intervalometer with automated or manual pan/tilt programing allowing for more customization. The CamRanger PT Hub will work with the existing MP-360, MP-101, Bescor, or Hague.
- Bescor Mp 101 Manual Cloaks Of Skyrim Frostfall How To Gameboy Color Emulator On Mac Spybot Professional Edition Crack Blade And Soul Low Fps Watson Service Microscope Serial Numbers Habbo Account Hacker V1.5 Download Sci Fi Epub Collection Rar Zoo Tycoon For Mac Online Toontrack Superior Drummer 2.0 Keygen Torrent.
Bescor Mp 101 User Manual
It's a popular and well-built device that is crying out for wireless control.
If you buy the very expensive CamRanger (~350 USD) for wireless control of your camera, there is an (expensive) accessory available that allows you to also control the Bescor MP-101. Many people love the CamRanger, but I find the system unstable, and when it hangs the server needs to be restarted, which is pretty annoying when it's on a mast 12m up in the air.
Bescor Mp-101 Manual Pdf
An alternative (and better) solution for wirelessly controlling a camera is DDServer which is donationware and runs on the same hardware as the CamRanger (the TP-Link MR3040, which costs around 40 USD when bought without the CamRanger firmware installed). I also find the interface of DSLRDashboard much better than that on the CamRanger.
You need to be (or know) a little bit of a nerd to install the DDServer firmware on the TPlink MR3040, but you're getting a better product and saving 300 USD.
However, DSLRDashboard can't control the Bescor MP-101 head, which is crucial for the mast jobs that I do, which is why I was really happy when I found this simple solution to wirelessly controlling it.
Parts
IC 2262 / 2272 4-channel remote-control kit (~ 4 USD on ebay)7-pin DIN plug and wire (Or you can cut the plug off the wired remote)
The IC2262/2272 is a wonderful system comprising a key fob with 4 buttons, and a tiny circuit board with 7 pins - power and ground plus a pin for each of the buttons (plus a pin that goes high when any of the buttons is pressed). And it needs the same 5v supply that the Bescor head uses, so you don't need an extra battery.
Construction
Decide which buttons you want to control which movements (I chose A=Left, B=Right, C=Up, D=Down))Bescor Mp-101 User Manual
Connect the corresponding pins to the 7-pin DIN plug.(Leave the VT pin on the board, and the speed pin on the DIN plug unconnected)And that's it ! Couldn't be simpler.
But it can be more complicated, if you want, so I have actually put an arduino microprocessor between the 2272 and the head so that I can do more complicated things in the future (eg programmed panorama stitching).
But that's a story for another day (see below).
Another day :The range of these remote controls is normally around 100m, but I found that was reduced significantly when I had the Bescor motor switched on, presumably due to electromagnetic noise interfering with the radio signals. The device still worked, but at longer distances the motor ran intermittently when a button was held constantly.
For this reason, plus future features, I added an arduino microcontroller between the receiver and the Bescor head, whose job was to create a one second pulseeach time a short signal was detected, thus smoothing out the noise (at the expense of the loss of a few degrees of positioning precision).
The wiring is pretty simple : Pins A,B,C, and D on the receiver are connected to Arduino input pins 8,9,10, and 11. VT is connected to pin 12, while ground and 5v are common to the Bescor, the receiver and the Arduino. Output pins 0, 1, 2, 3, and 4 on the Arduino are connected to the 7-pin DIN going to the Bescor.I also added an LED to pin 5, as a confirmation lamp.
Here you can pick up the Arduino code
© Mark Harris 2016, but feel free to distribute without changes.